新闻资讯

新闻资讯

current position: Home > News Center > Industry News

Electroplating equipment manufacturer shares: How to repair hydraulic systems and avoid abnormal pressure

2026-06-04 08:34:08
times

Guidelines for Maintenance and Overhaul of Hydraulic System Pressure Abnormalities in Electroplating Equipment

The hydraulic system is the core power unit of electroplating equipment, responsible for key actions such as lifting and lowering the plating tank, adjusting the anode position, and controlling the pressure of the filtration system. Abnormal pressure (too high, too low, fluctuation) can directly damage the stability of the electroplating process, leading to uneven coating thickness, missed plating, equipment failure, and other problems. Based on the practical experience of electroplating equipment manufacturers, the following sharing of maintenance methods and daily maintenance points for hydraulic system pressure abnormalities can help enterprises reduce downtime and ensure production efficiency.


1、 Common manifestations of abnormal pressure in hydraulic systems

1. Insufficient pressure: The system cannot reach the set pressure, the actuator components (such as hydraulic cylinders) move slowly or weakly, the plating tank lifting is stuck, and the anode adjustment is not in place.

2. Excessive pressure: Exceeding the rated pressure value can cause pipeline rupture, seal damage, and even lead to equipment safety accidents.

3. Pressure fluctuations: The pressure fluctuates between high and low, causing unstable movement of the executing components and affecting the uniformity of the coating (such as local coating being too thick due to shaking of the hanger).


2、 Maintenance steps for abnormal pressure

1. Security preprocessing

Before maintenance, the power supply of the equipment must be cut off, the hydraulic pump must be turned off, and the pressure relief valve must be opened to release the system pressure (to avoid oil splashing or unexpected component movement). Wear protective gloves and goggles to ensure a well ventilated operating environment.

2. Oil inspection

Oil is the "blood" of hydraulic systems, and oil quality issues are a common root cause of abnormal pressure:

-Oil level: Check the oil level gauge in the tank. If it is below the low mark, add hydraulic oil of the same brand (avoid mixing different brands or models).

-Oil quality: Observe the color of the oil (normally light yellow transparent, blackening/emulsification needs to be replaced), smell the odor (burnt smell indicates oil deterioration). Take samples to test viscosity and impurity content. If the impurities exceed the standard, empty the old oil, clean the oil tank and pipelines with a special cleaning agent, and then add new oil.

3. Hydraulic pump maintenance

The pump is the power source of the system, and wear or internal leakage can cause insufficient pressure:

-Listen to the sound: If there is sharp noise (cavitation) or dull abnormal noise (bearing wear) during operation, stop the machine for inspection.

-Pressure measurement: Use a pressure gauge to check the outlet pressure of the pump. If it is lower than the rated value, disassemble the pump body and check whether the blades and oil seals are worn, or whether there are cracks in the pump chamber (replace the pump components if necessary).

-Temperature: If the temperature of the pump body exceeds 60 ℃, it needs to be stopped, which may be due to internal leakage or high oil viscosity (replace with appropriate viscosity oil).

4. Inspection of valve components

Valve failure is the core cause of abnormal pressure:

-Overflow valve: Check if the set pressure is correct (calibrate with a pressure gauge), and if the valve core is stuck (disassemble and clean, replace if worn). If the overflow valve spring breaks, it will cause the pressure to fail to rise; If the valve core is stuck in the open position, the system pressure will continue to be too low.

-Directional valve: Check whether the valve core moves flexibly and whether there is internal leakage (observe whether the actuator moves automatically). Internal leakage can cause pressure loss and requires replacement of seals or valve cores.

-Pressure reducing valve: If there is a pressure reducing circuit, check if the pressure is stable (fluctuations may be due to valve core wear).

5. Maintenance of pipelines and joints

Leakage will directly reduce system pressure:

-Check whether the pipeline is cracked or deformed, and whether the joints are loose (apply soapy water to the joints, if there is bubbling, it is a leak). Tighten the joints or replace damaged pipelines (priority should be given to corrosion-resistant stainless steel pipelines to adapt to the humid environment of the electroplating workshop).

6. Perform component maintenance

Internal leakage of hydraulic cylinder/motor can cause abnormal pressure:

-Hydraulic cylinder: If there are oil stains or weak movement on the piston rod, it indicates that the piston seal is worn and needs to be replaced with oil resistant rubber seals (such as nitrile rubber).

-Hydraulic motor: Check if the output torque is normal and if there are any leaks (replace seals or motor components).


3、 Key points for daily maintenance to avoid abnormal stress

1. Regular inspection: Check the oil level every week, check the oil quality every month, clean the hydraulic filter element every quarter (or replace it according to the instructions) to prevent impurities from entering the system.

2. Oil management: Use hydraulic oil recommended by the manufacturer, use a filter funnel when refueling, and seal the oil tank cover to prevent water vapor and corrosive gases from entering and causing oil emulsification.

3. Component maintenance: Clean key valves such as overflow valves and directional valves every six months, and lubricate the bearings of the pump with specialized grease.

4. Operation specifications: Avoid overloading operation, prohibit working under high pressure for a long time, and release system pressure before shutdown.

5. Environmental protection: The electroplating workshop is humid and highly corrosive. Regular rust prevention treatment (such as spraying rust proof paint) should be carried out on the oil tank and pipeline, and residual electrolyte on the surface of the equipment should be cleaned.


summary

The maintenance of hydraulic system pressure abnormalities should follow the principle of "easy before difficult, external before internal", and daily maintenance is the key to preventing abnormalities. Through standardized maintenance procedures and regular upkeep, the lifespan of hydraulic systems can be effectively extended, ensuring stable operation of electroplating equipment and improving product quality. Enterprises should establish a hydraulic system maintenance ledger to record maintenance time and component replacement status, providing reference for subsequent maintenance.

Tags

Related news

  • menu